Nine ways to teach you how to choose a computerized flat knitting machine

The first trick: look at the nose

The machine head is the heart of the mechanical operation. The needle selector, cam, electromagnet, stitch and other machine head components drive the knitting needles to work. The core of the machine head is the triangular bottom plate. Proper selection of the triangular plate can increase the lifting speed and lifting frequency of the needle starting cam, reduce the damage rate of knitting needles, widen the adjustable range of fabric density, and improve the weaving quality of fabrics. . At present, domestic triangular production enterprises are limited by materials, heat treatment, cryogenic treatment, manufacturing and other technologies, and it is still difficult to compete with imported equipment. If the triangular bottom plate is not tough enough or the process is not up to standard, it will cause problems such as firing pins and fabric deformation. Seriously, it will cause mechanical problems. Worn, deformed, blackened.

The second trick: look at the system

The computer system should be the brain of the whole machine. It is conceivable that this metaphor shows the importance of the computer. If the computer is unstable, it must be a crime that affects the output and quality of sweaters. All movements, patterns, speed, and density must be controlled by the computer. The head and shaker flew off, the yarn feeder got messed up, the characters became loose after moving the needle a few times, the machine crashed, and it ran around and spent. It was really scary!

The third trick: look at the needle board

The needle board should be regarded as the trunk of the computerized flat knitting machine. It is also limited by materials, heat treatment, technology, manufacturing and other technologies. If the needle board is not selected properly, it will cause rough fabric, wear of the board parts, needle strike, and even blacken and ulceration of the needle board. . If the fabric is not assembled properly, the stitches will go away.

The fourth trick: look at the knitting needles

The knitting needle is the finger of the computerized flat knitting machine. The warp and weft knitting of the yarn depends entirely on it. In addition to the material toughness of the knitting needle, the design and precision of the hook and latch of the needle head are also very different.

The fifth trick: look at the service

Mechatronic machinery and equipment will inevitably have problems. Stoll should be one of the better equipment in the industry, but common failures such as crashes, frequent failures of the pulling system, and damage to scissors will also occur, so no matter what the machine is, it is not " Admiralty," sure has its bad days.

Sixth trick: look at the background

This is very important. There are two types of computerized flat knitting machine manufacturers: one is the former manufacturer of needle and spinning machinery equipment; I have heard that there are construction companies and advertising companies in this industry. It doesn’t mean that those who change careers are not good at making equipment, but the industry is like a mountain. The blueprints were modified from east to west, and changed into four different images.

The seventh trick: look at the printing software

There are many kinds of pattern-making software, and the functions of pattern-making software are basically the same. It mainly depends on which pattern-making software is used by more people in this industry. Pattern-making software has a large market share in China. It is not difficult to recruit such pattern-making masters. There are more people.

The eighth trick: look at the employment penetration rate

It is not advisable for sweater factories to rely too much on the after-sales service of computerized flat knitting machine manufacturers without training their own machine repair team, because the after-sales service team of computerized flat knitting machine manufacturers cannot stay in sweater factories forever.

Ninth trick: choose the model, just fit it

Whether it is suitable for your own production requirements, such as whether the goods are thick needles or thin needles, if the needles are thick, you must consider the dual system, because there are many patterns that can be made and the efficiency is high, the efficiency of the single system is basically incomparable. If it is a fine needle, it can be compared in many ways. If it is a single-sided or twisted flower, the pattern does not need to be too much, and it is used to run the volume. Consider the single system. If the funds are not too tight, it is recommended to choose dual systems, and the prices are similar. From the perspective of long-term development and actual benefits, dual systems still have advantages.